从城市规划与发展角度对军民合用机场的反思——以济宁曲阜机场为例

以济宁曲阜机场为例,结合菏泽机场规划,说明了济宁曲阜机场存在机场位置与旅游景区位置发生偏离、对济宁城市空间扩展引导不足、限制菏泽机场规划、影响济宁综合交通枢纽建设以及机场容量无法满足旅客量增长等问题,这些问题具有一定的普遍意义,希望能促进规划和决策者对军民合用这一机场建设方式采取更为谨慎的态度.     

小型固定翼无人机集群综述和未来发展综述

围绕小型固定翼无人机集群这一难度高、发展快、应用前景广阔、多学科交叉的新方向,从集群系统内涵、现有典型项目、关键技术3个角度综述了国内外小型固定翼无人机集群的研究现状。在系统梳理集群系统内涵和应用优势的基础上,从集群协同模式探索、分布指挥体系构建、核心关键技术突破和集群验证等4个视角总结现有典型项目,从体系架构、通信组网、决策与规划、飞机平台、集群飞行、集群安全与集群指控等7个核心点综述了技术研究现状。最后,综合小型固定翼无人机集群中亟需解决的关键技术,展望了这一领域未来的发展趋势。     

膨胀效应对激波/湍流边界层干扰的影响

采用直接数值模拟方法对来流马赫数2.9,30°激波角的入射激波与膨胀角湍流边界层干扰问题进行了数值研究。入射激波在壁面上的名义入射点固定在膨胀角角点,膨胀角角度分别取为0°、2°、5°和10°。通过改变膨胀角角度,考察了膨胀效应对干扰区内复杂流动现象的影响规律和作用机制,如分离泡、物面压力脉动特性、膨胀区湍流边界层和物面剪切应力脉动场等。研究发现,膨胀角角度的增大使得分离区流向长度和法向高度急剧降低,尤其是在强膨胀效应下分离泡形态呈现整体往下游偏移的双峰结构。物面压力脉动功率谱结果表明,膨胀角为2°和5°时,分离激波的非定常运动仍表征为大尺度低频振荡,而膨胀角为10°,强膨胀效应极大地抑制了分离激波的低频振荡,加速了下游再附边界层物面压力脉动的恢复过程。膨胀区湍流边界层雷诺剪切应力各象限事件贡献和出现概率呈现逐步恢复到上游湍流边界层的趋势,Görtler-like流向涡结构展向和法向尺度变化剧烈,同时在近壁区将诱导生成大量小尺度流向涡。此外,物面剪切应力脉动场的本征正交分解分析指出,膨胀效应的影响体现在低阶模态能量的急剧降低从而使得高阶模态的总体贡献相对升高。     

导流槽构型对火箭起飞时流场和声场的影响

为了研究四喷管运载火箭起飞时火箭周围噪声环境问题,建立燃气/空气双组分的可压缩流动模型,采用2阶Roe格式、SAS(scale-adaptive simulation)湍流模型和声学类比积分法Ffowcs-Williams Hawkings(FW-H)求解三维Navier-Stokes方程。以单机火箭的噪声问题为对象开展数值模拟,并将噪声数值计算结果与试验数据对比,误差在3dB以内(相对误差小于1.6%),验证预测噪声方法的有效性,进而研究四喷管运载火箭起飞阶段采用不同导流槽构型对箭体舱段区域噪声环境的影响,结果表明:在相同噪声接收点处,单侧导流槽对应的总声压级比双侧导流槽大,两者的总声压级(OASPL)之差最大为10.7dB。另外,当采用单侧导流槽时,沿周向接收点的噪声总声压相对单侧导流槽中心截面呈对称分布,而且沿导流出口方向逐渐增大。所建立的噪声数值方法为大推力捆绑运载火箭舱段的噪声环境预测及其控制提供一定参考。     

基于实战使用的涡轴发动机空中起动飞行试验

以涡轴发动机实战使用中空中紧急起动相关技术指标和特情处置措施验证为目的,设计了贴近实战使用特征的发动机空中起动试飞方案,并以某涡轴发动机设计定型试飞为依托,进行了不同飞行工况下的飞行试验验证和数据分析研究。结果表明:该空中起动试飞方案合理可行,能够最大程度的贴近部队实战使用的技术特征,满足对发动机起动高度包线、起动时间等研制总要求规定的技术指标验证需求;试飞结果表明该型涡轴发动机4000m以上高度停车至再起动期间直升机平均下滑高度约为670m,平均停车时间约为185s。该试飞方法和数据结果可为部队实战使用过程中空中遭遇停车的紧急处置提供支持和参考。     

主流攻角对双射流孔气膜冷却特性的影响

应用压力敏感漆技术,在平板上测量了不同主流攻角(i=-30°,-20°,-10°,0°,10°,20°,30°)下双射流孔的气膜冷却效率,并利用计算流体动力学(CFD)计算得到的流场对气膜冷却效率的规律进行了解析。所研究的双射流孔结构的孔间无量纲横向距离为0.5,孔间无量纲流向距离为3;射流与主流密度比为1.0,吹风比分别为0.5、1.0、1.5、2.0。结果表明小的主流攻角(i=-10°,0°,10°)下,流场中存在反肾型涡对或挤压作用,气膜层与壁面贴附良好,气膜冷却效率最高;大正值攻角(i=20°,30°)下,虽然气膜覆盖面积大,但反肾型涡对退化,气膜冷却效率下降;大负值攻角(i=-20°,-30°)下,流场中有肾型涡对,且气膜横向覆盖受限,气膜冷却效率最低。     

Flow separation control on swept wing with nanosecond pulse driven DBD plasma actuators

A 15° swept wing with dielectric barrier discharge plasma actuator is designed.Experimental study of flow separation control with nanosecond pulsed plasma actuation is performed at flow velocity up to 40 m/s. The effects of the actuation frequency and voltage on the aerodynamic performance of the swept wing are evaluated by the balanced force and pressure measurements in the wind tunnel. At last, the performances on separation flow control of the three types of actuators with plane and saw-toothed exposed electrodes are compared. The optimal actuation frequency for the flow separation control on the swept wing is detected, namely the reduced frequency is 0.775, which is different from 2-D airfoil separation control. There exists a threshold voltage for the low swept wing flow control. Before the threshold voltage, as the actuation voltage increases, the control effects become better. The maximum lift is increased by 23.1% with the drag decreased by 22.4% at 14°, compared with the base line. However, the best effects are obtained on actuator with plane exposed electrode in the low-speed experiment and the abilities of saw-toothed actuators are expected to be verified under high-speed conditions.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

超声速串列静叶积叠优化分析

在进口超声速、气流转折角大的高负荷条件下,静叶通道中激波强度高,激波、附面层干扰引起的损失大,且静叶中三维流动引起的径向载荷分布不均匀,易产生角区分离。叶片积叠优化是提高风扇性能的一项有效技术。采用数值模拟的方式研究了不同积叠形式对优化串列静叶沿展向激波结构,改善叶排间流动匹配的作用。三维流动对比分析可以得出:高负荷串列静叶采用正弓形积叠,叶片展向载荷分布合理,静叶端壁角区分离损失减小,前后叶片排流动匹配较好,风扇性能进一步提高。     

三维数模随动下的机翼结构重量优化

目前,基于快速建模下的重量重心估算系统得到了快速发展。为了进一步提高结构重量估算精度,研究了如何在重量重心快速分析(WCGA)系统环境中构建优化模块。以机翼结构重量优化为例,提出优化流程,对优化模块功能进行分解,给出模型简化要求。以A320飞机机翼为例,对梁和长桁进行优化,结果显示,经过优化,有效减轻了结构重量,且相比于传统的减重优化设计方法,极大提高了计算效率。